مقاله انگلیسی رایگان در مورد فرسودگی جوش آلومینیوم – الزویر 2018

 

مشخصات مقاله
ترجمه عنوان مقاله فرسودگی جوش آلومینیوم: از خصوصیات تا قوانین طراحی
عنوان انگلیسی مقاله Aluminium weld fatigue: From characterisation to design rules
انتشار مقاله سال 2018
تعداد صفحات مقاله انگلیسی 22 صفحه
هزینه دانلود مقاله انگلیسی رایگان میباشد.
پایگاه داده نشریه الزویر
نوع نگارش مقاله
مقاله پژوهشی (Research Article)
مقاله بیس این مقاله بیس نمیباشد
نوع مقاله ISI
فرمت مقاله انگلیسی  PDF
ایمپکت فاکتور(IF)
0.970 در سال 2018
شاخص H_index 51 در سال 2019
شاخص SJR 0.277 در سال 2018
شناسه ISSN 1877-7058
مدل مفهومی ندارد
پرسشنامه ندارد
متغیر ندارد
رفرنس دارد
رشته های مرتبط جوشکاری
گرایش های مرتبط بازرسی جوش، صنایع فلزی
نوع ارائه مقاله
ژورنال و کنفرانس
مجله / کنفرانس پروسیدیای مهندسی – Procedia Engineering
دانشگاه  Gestamp Chassis, Skerne road, DL5 6EP, UK
کلمات کلیدی آلومینیوم، فرسودگی، اتصالات جوش داده شده، جوشکاری شکاف با مهندسی به کمک رایانه، آزمایش و تغییر شکل
کلمات کلیدی انگلیسی Aluminium, fatigue, welded joints, CAE SeamWeld, testing and distortion
شناسه دیجیتال – doi
https://doi.org/10.1016/j.proeng.2018.02.051
کد محصول  E12495
وضعیت ترجمه مقاله  ترجمه آماده این مقاله موجود نمیباشد. میتوانید از طریق دکمه پایین سفارش دهید.
دانلود رایگان مقاله دانلود رایگان مقاله انگلیسی
سفارش ترجمه این مقاله سفارش ترجمه این مقاله

 

فهرست مطالب مقاله:
Abstract

1. Introduction

2. Nomenclature

3. SeamWeld fatigue approach

4. Fatigue design curve generation – Test/FEM

5. Correlation on subframes / suspensions

6. Welding distortion effect on fatigue

7. Conclusion

References

 

بخشی از متن مقاله:
Abstract

In suspension design, traditionally subframes and links are welded structures, with one of the main design criteria being fatigue. Better understanding, correlation and correct design rules are vital to ensure safety and avoid over design that can lead to a reduction in competitiveness. A known mesh modelling T-joint SN method is used to design the welds and is mainly driven from standards used for thicker panels seen in the construction and ship building industry. To consider the thin sheet designs largely seen in automotive, Volvo & nCode have developed a new method based on structural stress and is known to be mesh insensitive. However, new difficulties emerged due to the clear separation between the membrane and bending behaviour needed for stress recovery. Specific tests need to be defined to ensure correct characterisation. Gestamp has generated a new standard of design rules to ensure correlation in Weld-Ends and in Mid-Weld cracks and correct toe position definition to ensure accurate stress recovery, and give more beneficial input to process by better defining the weld torch position. New test specimens have been developed and intensive testing carried out to fully characterise the bending and tension behaviour and reduce the gap in predictions between Lap Weld and Fillet Weld. This methodology has been successfully used in suspension designs with high confidence and correlation. These design rules have been used in conjunction with studying the effect of weld process and sequence on fatigue performance. Controlled distortion subframes, against high distortion subframes, have been tested to capture the benefit by reducing the fit-up gaps. Residual stresses are still a grey zone for Gestamp and further work is needed to better understand the effect.

Introduction

With the increase demand for reduction of weight and cost in the automotive industry, defining and correlating the design rules is becoming key to ensure accurate predictions in terms of fatigue performance to eliminate overengineering. There is a clear correlation between robustness and accuracy of CAE (FEM) predictions and reduction in cost and weight. Aluminium is seeing more widespread use in the automotive sector to reduce the weight and this drives a need to define new design rules and weld process control to ensure quality and safety. Critical to defining these design rules is the analysis of the limits of the current methods and develop a range of testing to correlate all the predictions. Controlling the process and especially weld distortion is more important when dealing with aluminium due to high thermal conductivity and coefficient of thermal expansion which leads to larger heat affected zones and higher distortion compared to steel. In addition, penetration and fit-up gap have more effect compared to those seen in welding steel.

دیدگاهتان را بنویسید

نشانی ایمیل شما منتشر نخواهد شد. بخش‌های موردنیاز علامت‌گذاری شده‌اند *

دکمه بازگشت به بالا