مشخصات مقاله | |
ترجمه عنوان مقاله | اثر دما و میزان کشش بر خصوصیات ماده Al319-T7 |
عنوان انگلیسی مقاله | Effect of Temperature and Strain Rate on Material Characteristics of Al319-T7 |
انتشار | مقاله سال 2018 |
تعداد صفحات مقاله انگلیسی | 16 صفحه |
هزینه | دانلود مقاله انگلیسی رایگان میباشد. |
پایگاه داده | نشریه الزویر |
نوع نگارش مقاله |
مقاله پژوهشی (Research Article) |
مقاله بیس | این مقاله بیس نمیباشد |
نوع مقاله | ISI |
فرمت مقاله انگلیسی | |
ایمپکت فاکتور(IF) |
0.970 در سال 2018 |
شاخص H_index | 51 در سال 2019 |
شاخص SJR | 0.277 در سال 2018 |
شناسه ISSN | 1877-7058 |
مدل مفهومی | ندارد |
پرسشنامه | ندارد |
متغیر | ندارد |
رفرنس | دارد |
رشته های مرتبط | مهندسی مکانیک، جوشکاری |
گرایش های مرتبط | ساخت و تولید، صنایع فلزی |
نوع ارائه مقاله |
ژورنال و کنفرانس |
مجله / کنفرانس | پروسیدیای مهندسی – Procedia Engineering |
دانشگاه | The University of Michigan-Dearborn, 4901 Evergreen Road, Dearborn, MI4812, USA |
کلمات کلیدی | فرسودگی مکانیکی و حرارتی، آلیاژ آلومینیوم قالبی، درجه حرارت بالا، رفتار چرخه ای، پاسخ به کشش و تنش |
کلمات کلیدی انگلیسی | thermomechanical fatigue; cast aluminum alloy; high temperatre; cyclic behavior; stress-strain response |
شناسه دیجیتال – doi |
https://doi.org/10.1016/j.proeng.2018.02.079 |
کد محصول | E12682 |
وضعیت ترجمه مقاله | ترجمه آماده این مقاله موجود نمیباشد. میتوانید از طریق دکمه پایین سفارش دهید. |
دانلود رایگان مقاله | دانلود رایگان مقاله انگلیسی |
سفارش ترجمه این مقاله | سفارش ترجمه این مقاله |
فهرست مطالب مقاله: |
Abstract
1. Introduction 2. Experimental description 3. Results and Discussion 4. Conclusion References |
بخشی از متن مقاله: |
Abstract
An extensive experimental investigation of different temperatures and strain rates has been carried out on aluminum alloy Al319-T7. It is found that elevated temperature tends to decrease the strength in tensile and cyclic tests, whereas increasing strain rate appears to improve the strength, and in strain-controlled isothermal fatigue tests, higher temperature results in shorter fatigue life for a given stress amplitude. In addition, increased strain rates are found to improve the fatigue life in high-temperature tests, while their effect is negligible in room-temperature tests. In-phase (IP) and out-of-phase (OP) thermo-mechanical fatigue (TMF) tests with and without dwell time are also conducted in this paper. The results reveal that for the same applied total strain amplitude, OP tests, owing to their larger mechanical strain amplitude, are more critical than IP tests. Furthermore, stress relaxation happening in dwell time will help to increase the fatigue life, compared to those tests without dwell time. Introduction Nowadays, aluminum alloys are used more frequently to replace cast iron and steels in various mechanical and structural components of vehicles for the purpose of increasing fuel economy by reducing weight. One typical use is in the cylinder heads of internal combustion engines, the operating temperatures of which have been increased to improve engine efficiency. The peak temperature they may experience is up to 300˚C [1]. These components subjected to high cyclic thermal and service loads are prone to fatigue failure. Thus, proper understanding of the material behavior at high temperatures is required. Engler-Pinto et al. [2] investigated the thermo-mechanical fatigue behavior of cast 319 aluminum alloys under high temperatures and found the stress-strain behavior is similar between in-phase and out-of-phase TMF tests. Under a given mechanical strain amplitude, fatigue life in IP tests is lower compared to OP tests. By using a twostate-variable unified inelastic constitutive model proposed by Sehitoglu [3], Engler-Pinto et al. [4] determined the constants in this model systematically from isothermal experiments and verified its ability to simulate the material response, including cyclic softening and thermal recovery, by comparing it with TMF experimental results. |