مقاله انگلیسی رایگان در مورد سختی سطح قطعات Ti-6Al-4V – الزویر ۲۰۱۸

elsevier

 

مشخصات مقاله
ترجمه عنوان مقاله سختی سطح قطعات Ti-6Al-4V به دست آمده توسط ذوب لیزر انتخابی (SLM) و ذوب پرتو الکترونی (EBM): تأثیر بر عمر فرسودگی چرخه بالا
عنوان انگلیسی مقاله Surface roughness of Ti-6Al-4V parts obtained by SLM and EBM: Effect on the High Cycle Fatigue life
انتشار مقاله سال ۲۰۱۸
تعداد صفحات مقاله انگلیسی ۹ صفحه
هزینه دانلود مقاله انگلیسی رایگان میباشد.
پایگاه داده نشریه الزویر
نوع نگارش مقاله
مقاله پژوهشی (Research Article)
مقاله بیس این مقاله بیس نمیباشد
نوع مقاله ISI
فرمت مقاله انگلیسی  PDF
ایمپکت فاکتور(IF)
۰٫۹۷۰ در سال ۲۰۱۸
شاخص H_index ۵۱ در سال ۲۰۱۹
شاخص SJR ۰٫۲۷۷ در سال ۲۰۱۸
شناسه ISSN ۱۸۷۷-۷۰۵۸
مدل مفهومی ندارد
پرسشنامه ندارد
متغیر ندارد
رفرنس دارد
رشته های مرتبط مهندسی مکانیک، ریاضی
گرایش های مرتبط ساخت و تولید، آنالیز عددی
نوع ارائه مقاله
ژورنال و کنفرانس
مجله / کنفرانس پروسیدیای مهندسی – Procedia Engineering
دانشگاه  Arts et Metiers Paristech, I2M, CNRS, Talence 33400, France
کلمات کلیدی فرسودگی چرخه بالا، ذوب لیزر انتخابی، ذوب پرتو الکترونی، سختی سطح، Ti-6Al-4V، روش عنصر محدود
کلمات کلیدی انگلیسی HCF; SLM; EBM; Surface Roughness; Ti-6Al-4V; FEM
شناسه دیجیتال – doi
https://doi.org/10.1016/j.proeng.2018.02.010
کد محصول  E12454
وضعیت ترجمه مقاله  ترجمه آماده این مقاله موجود نمیباشد. میتوانید از طریق دکمه پایین سفارش دهید.
دانلود رایگان مقاله دانلود رایگان مقاله انگلیسی
سفارش ترجمه این مقاله سفارش ترجمه این مقاله

 

فهرست مطالب مقاله:
Abstract

۱٫ Introduction

۲٫ Materials and Methods

۳٫ Results and Discussions

۴٫ Conclusion

References

 

بخشی از متن مقاله:
Abstract

Selective Laser Melting (SLM) and Electron Beam Melting (EBM) are powder bed fusion processing which allows to build-up parts by successive addition of layers using 3D-CAD models. Among the advantages, are the high degree of freedom for part design and the small loss of material, which explain the increase of Ti-6Al-4V parts obtained by these processes. However, Ti-6Al-4V parts produced by SLM and EBM contain defects (surface roughness, porosity, tensile residual stresses) which decrease significantly the High Cycle Fatigue (HCF) life. In order to minimize the porosity and tensile residual stresses, post-processing treatments like Hot Isostatic Pressing (HIP) and Stress Relieving are often conducted. But the modification of the surface roughness by machining is very costly and not always possible, especially for parts with complex design. The aim of this work is to evaluate the effect of the surface roughness and microstructure of Ti-6Al-4V parts produced by SLM and EBM on the HCF life. Five sets of specimens were tested in tension-compression (R=-1; f=120Hz): Hot-Rolled (reference); SLM HIP machined; SLM HIP As-Built; EBM HIP machined; EBM HIP As-Built. For each condition, microstructure characterization, observation of the fracture surface of broken specimens and surface analysis were carried out respectively by Optical Microscope (OM), Scanning Electron Microscope (SEM) and 3D optical profilometer. Results of fatigue testing show a significant decrease of the HCF life mainly due to the surface roughness. Along with experimental testing, numerical simulations using FEM were conducted using the surface scans obtained by profilometry. Based on extreme values statistics of the crossland equivalent stress averaged on a critical distance, a methodology is proposed to take into account the effect of the surface roughness on the HCF life.

Introduction

These defects lead to an early initiation of the fatigue cracks and it is well known that, before any posttreatment, the HCF strength of the as-built specimens is not suitable for aircraft loadbearing applications [9]. It is also hard to quantify and understand the respective influence of these defects since in many studies, the early crack initiation is mostly due to a combination of the porosity, surface roughness, residual stresses and brittle microstructure [3, 9, 10]. Moreover the additively manufactured specimens used for aircraft applications are almost systematically stress-relieved and HIP.On the other hand, the surface roughness is not always removable since the parts may have a very complex shape. It is then very important to understand its effect on the HCF strength. This study compares results of HCF tests on SLM and EBM stress-relieved HIP specimens with either machined or as-built surfaces. This procedure allows eliminating both residual stresses and porosity, homogenizes the microstructure of the samples and to highlight the effect of the surface roughness. Along with experimental testing, numerical simulations using FEM were conducted using the surface scans obtained by profilometry. There are many existing models accounting for the effect of the surface roughness on the HCF strength [11–۱۴] but only for periodic roughness obtained by machining.

ارسال دیدگاه

نشانی ایمیل شما منتشر نخواهد شد. بخش‌های موردنیاز علامت‌گذاری شده‌اند *